CO2 Pressure Transfer Kit for Ss Brewtech Chronical Fermenters

CO2 Pressure Transfer Kit for Ss Brewtech Chronical Fermenters
Part Number: Ss-CO2-KO
Brand: Brewhouse Hardware
List Price: $74.99
Your Price: $59.95
Qty
Safe and Secure Shopping at Keg Outlet

CO2 Pressure Transfer Kit for Ss Brew Tech Chronical Fermenters

This CO2 Transfer kit is designed specifically for the Ss Brewing Technologies Conical Fermenters.  It features a 1.5" Tri-Clamp fitting which connects directly to the top of your Ss BrewTech Fermenter.  The 0-15 PSI gauge is accurate at low pressures which is needed with transferring your beer.  NEVER Exceed 1-2 PSI in your Chronical fermenter!

Our CO2 Keg Transfer Kits are designed to force your beer from your conical fermenter to your homebrew keg with ease, while limiting the amount of contact that your beer has with the outside air.  This will help preserve and ensure that you get the best flavors and aromas from your beers, as well as cut down on the risk of any contaminants falling into your fermenter during the transfer. Keep your beers clean and your hoppy IPA's smelling as aromatic as possible by keeping oxygen away from them.  Use our CO2 Kegging kits and you will never go back to regular gravity transfers!


Notes

Our Guarantee
We not only sell all the products on our site, but we also use them. And we stand behind everything we sell.

This kit contains:

  • 4 ft Red CO2 Gas Hose
  • 1 - 5/16" Stainless Steel Swivel Nuts
  • 2 - Oetiker Clamps
  • 1/4" NPT 304 Stinless Steel Tee
  • 1.5" Tri-Clamp to 1/4" NPT 304 Stainless Steel Sanitary Fitting
  • 0-15 PSI CO2 Gauge
  • 1/4" NPT to 5/16" Barb 304 Stainless Steel Fitting

Scroll to view all product options.

Part # Description Price
Ss-CO2-KO CO2 Pressure Transfer Kit for Ss Brewtech Chronical Fermenters $59.95 Add to Cart

Scroll to view all product options.

Product Rating

4.5 out of 5, based on 26 user ratings.
4 total user reviews. View All Reviews

Share your thoughts with other customers

  Write Your Own Review

13 out of 13 found the following review helpful

5

This review is for anyone considering this! April 1, 2015

Who is this CO2 Pressure Transfer Kit for?
This is for anyone with a conical fermenter that has a tri-clamp fitting on the lid.

What does this CO2 Pressure Transfer Kit do?
This kit allows you to "force" beer out of your fermenter into your keg. Without a pressure transfer kit like this one, you'll need to use either gravity or a siphon. Gravity will require the fermenter to be positioned higher than your keg - this can be a tough proposition for anyone with a large fermenter. Siphon? No. Why not just use a bucket or carboy. Don't. You'll lose many of the benefits of using a conical fermenter.

How does this connect to the Chronical fermenter?
Simply, it uses a tri-clamp fitting. All you need is a tri-clamp and a gasket in order to attach this to your fermenter.

How is this connected to CO2?
The attached swivel nut on the gas hose allows for easy connection to most regulators. Once connected to the regulator, it is easy to test the pressure by turning on the CO2 flow, adjusting your regulator and pluggin the out valve on the tri-clamp. A 1-3psi transfer pressure is recommended. It can be hard to dial the pressure in depending on your regulator, but the attached low pressure regulator is great! My regulator did not register any pressure and the low pressure gauge on this CO2 Transfer Kit read at approximately 1.5psi.

Transferring beer
Once connected to CO2 and the pressure is dialed in between 1-3psi, you can begin pressurizing the fermenter. Once the fermenter has been pressurized, you can open the valve to begin transferring your beer to a keg. Note: you'll need a hose connected to the fermenter to allow the beer to flow into your keg.

Help other customers find the most helpful reviews
Was this review helpful? Yes / No

2 out of 4 found the following review helpful

3

Great for the purpose, wish it had an option... April 1, 2015

For the purpose intended, this kit is great. It allows you to apply (and measure) pressure to my conical fermenter. I've successfully "pushed" a batch of beer from my conical to my keg with no problems. This product does what it is meant to do.

Why did I give this product 3 stars? I feel like this product should have options. I did not need the swivel nut on the end. I happen to have a tank/regulator that will be dedicated to pressure transfers. My regulator happened to have a barb on the end. Easy enough fix. I just cut the swivel nut off and attached the hose to my regulator, but I think this product could be improved with the option to choose your connection type.

Help other customers find the most helpful reviews
Was this review helpful? Yes / No

3 out of 6 found the following review helpful

5

This product works great! February 12, 2015

I love being able to push my hoppy beers directly into the keg without exposing them to oxygen.

Between the Ss Brew Tech fermenters, my fermentation fridge and now my pressure transfer kit from Brewhouse Hardware, my beer is becoming top notch!

Help other customers find the most helpful reviews
Was this review helpful? Yes / No

1 out of 3 found the following review helpful

5

The Only Way to Keg from Your Conical Fermenter! February 12, 2015

Love using this method to keg from my Chronical Fermenter!!

Help other customers find the most helpful reviews
Was this review helpful? Yes / No

Fits These Applications:

Year Make Model SubModel Engine Transmission Drive